Boss Audio - BOSS Audio Systems AR3000D Armor Series Class D Monoblock Car Amplifier - 3000 High Output, 1 Ohm Stable, Low Level Inputs, Low Pass Crossover, MOSFET, Hook Up To Subwoofer For Bass

Click to view additional BOSSA AR3000D image

BOSS Audio Systems AR3000D Armor Series Class D Monoblock Car Amplifier - 3000 High Output, 1 Ohm Stable, Low Level Inputs, Low Pass Crossover, MOSFET, Hook Up To Subwoofer For Bass

Boss Audio AR3000D

Features

Monoblock
Class D Topology
1 Stable
PWM MOSFET Power Supply

Quick Specs

Type: Amplifiers
Width: 6.5"
Height: 2.7999999999999998224"
Depth: 12.3125"
Energy Star Rated: No

See More

QTY

URL

1 Ohm Stable The lowest impedance accepted by this amplifier is 1 ohm. Amplifiers that are 1 ohm stable produce the most power possible from the amp. An amplifier capable of delivering power at a 1 ohm load is usually reserved for serious subwoofers that can handle the power. Please note this particular amp needs a healthy electrical system including a low gauge wire capable of delivering the necessary current.

Class D Amps Class D is a high speed switching amplifier technology that is more efficient, generates less heat and draws less power than traditional Class A/B amps. We use Class D in our monoblock amplifiers to give you massive amounts of power in a relatively small footprint for clean, powerful, bass.

Phase Control The phase control feature allows you to adjust the speakers phase to ensure all audio signals are playing together rather than against each other. When bass notes are noticeably absent, a quick and easy adjustment to the phase control could provide the perfect remedy.

Protection If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself.

Strapping Capability Strapping capability means that two amplifiers can be linked together to create double the power at an impedance of 2 ohms. A benefit of strapping is less electrical current is required than if you ran [2] individual amps at 1 ohm and you only need 1 pair of preamp outputs and [1] RCA cable to connect.

Subsonic Filter A subsonic filter is designed for use on subwoofers. Since not all subwoofers can reproduce the same low frequencies, the subsonic filter can be set for optimum bass response in order to keep the driver playing efficiently.

Subwoofer Level Control The ability to boost or attenuate the sub level when an amp and subwoofer are connected to the subwoofer pre-amp output.

Switchable Input Sensitivity Switchable Input Sensitivity gives you the freedom to connect the amp to any standard source unit and have peace of mind it will be within range to properly match the output of the source unit allowing you to use the volume controls on your source unit the way it was designed.

Variable Bass Boost Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Variable Gain Control Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. To much gain will lead to distortion and to little will lead to clipping.

Variable Low Pass Filter Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Features

Monoblock
Class D Topology
1 Stable
PWM MOSFET Power Supply
RCA In/Out
Low Pass Filter
Subsonic Filter
Bass Boost
Input Sensitivity
Phase Control
Remote Subwoofer Control
Strapping Capable
Thermal, Short and Overload Protection Circuits

General Specs
Amp Topology	Monoblock, Class D
Power Supply Type	MOSFET Power Supply
Performance Specs
Total Power Output	3000 Watts
Peak Power @ 1	3000 Watts x
Peak Power @ 2	1500 Watts x
Peak Power @ 4	750 Watts x
RMS Power @ 1	2250 Watts x
RMS Power @ 2	1125 Watts x
RMS Power @ 4	563 Watts x
Strapped Power bridged @ 2	6000 Watts
Speaker Impedance	1 to 8
T.H.D. (Total Harmonic Distortion)	0.01 %
Frequency Response	15 Hz to 250 " "
Connections, Controls, and Processing
RCA Inputs	2 Channel
Pre Amp Outputs	2 Channel
Low Pass Filter	50 Hz to
Subsonic Filter	15 Hz to
Bass Boost	Variable " "
Phase Control	0 to
Subwoofer Level Control
Input Sensitivity Switch
Strappable
Thermal/Overload/Short Protection

Quick Specs

Appearance
Type: Amplifiers
Dimensions
Width: 6.5"
Height: 2.7999999999999998224"
Depth: 12.3125"
Features
Energy Star Rated: No

Get Adobe Reader

* Documents require Adobe Reader.

Watch Video

Professional delivery and installation is available for every product we sell. We would be happy to coordinate delivery and installation for you.

Extended warranties are usually very inexpensive and can save you thousands in the future. It's simple and inexpensive to purchase extended warranties and one of the smartest ways to protect your investment.

Electronics can be large, heavy and expensive. You probably don't have the special tools or expertise needed to fix them in a crisis. If you can spare a few thousand dollars without batting an eyelash for new electronics should they break tomorrow, don't buy a warranty. But if you're like most of us, protect yourself by purchasing inexpensive extended warranties when you buy a new product and save yourself big money in the long run.